OZDAT http://ozdat.com.au/forum/ |
|
Datsun 1000 Project :) http://ozdat.com.au/forum/viewtopic.php?t=31228 |
Page 1 of 1 |
Author: | d [ Sat May 18, 2013 2:40 pm ] |
Post subject: | Re: Datsun 1000 Project :) |
http://datsun1000.com/TopicView.asp?Top ... 1#Post6953 |
Author: | k-man 79 wagon [ Sat May 18, 2013 6:09 pm ] |
Post subject: | Re: Datsun 1000 Project :) |
12a bridgy would be mad |
Author: | d [ Mon May 20, 2013 12:33 am ] |
Post subject: | Re: Datsun 1000 Project :) |
anything over 1985cc is not allowed in QLD 12a is rated at 2400cc An L16 can fit with side marine mechanical waterpump and custom sump (L20 crank fits with L16 rods & Z20E pistons if you line bore the L16 block and bore to 85mm (2mm over) or 3mm over for +1mm 86mm Z20E slugs. Source a Z18et top end but use intercooler and t28bb turbo and L16 is on the side of your block but 2LT turbo & easy 5 speed |
Author: | da fonz [ Mon May 20, 2013 8:16 am ] |
Post subject: | Re: Datsun 1000 Project :) |
hahaha d! you successfully just confused the crap out of me just then! wouldnt it just be easier to fit a ca18det + box and go to a wreckers and buy a dead ca16de for the engine number to use on the ca18det? like i said i have a complete ca18det here just need a wiring loom. going to sus out the front disk brakes this week. Fonz |
Author: | d [ Wed May 22, 2013 12:29 am ] |
Post subject: | Re: Datsun 1000 Project :) |
enlargement of an L16 is very different to re-stamping Plus a bonus is no pollution gear |
Author: | da fonz [ Wed May 22, 2013 7:43 am ] |
Post subject: | Re: Datsun 1000 Project :) |
we have decided to go ca16det and engine is on its way do you recommend a diff thats the simplest to adapt to the 1000 rear end? i have been told to use a 2wd 5 stud hilux rear diff? as we are going to use BA falcon xr6 turbo front brakes up front. Fonz |
Author: | d [ Wed May 22, 2013 12:27 pm ] |
Post subject: | Re: Datsun 1000 Project :) |
Could also have gone for a sleeved 85mm ca16det bottom end using Honda pistons that would guarantee engineering and more capacity. Do you know what the ca18det you are getting has or any specs you might have? Well xr6 brakes! wow would like to see that! but sounds heavy with 5 stud setup. You can do a silvia front setup and shortened Kia Sportage twin cam rear end w/LSD. Not all Sportages have an LSD its an option but easy to find and 7.5 inch diff way bigger than needed for such little weight and same size as rotary rx7 s3 rear ends so total weight 800kg is about 300-500kg less than Mazda rx7 s3 or mx5 etc. http://www.ebay.com.au/itm/Miata-94-up- ... 53f906c5aa |
Author: | da fonz [ Wed May 22, 2013 3:30 pm ] |
Post subject: | Re: Datsun 1000 Project :) |
yeah could of gone the ca16 but found a cheap ca18det that is complete with t28 bb turbo and nistune ecu :d made 225rwkw before being removed to make way for a rb25/30 so cant complain on the hunt for a bare ca16de block to re stamp the ca18det and yes xr6 rotors will be a bit of a challenge but my fabricator recons we can work something out. i will be postin progress pics and a full build thread once we start going with it. engine arrives this saturday so getting ready for some greasy hands and late nights. we want to debut it at 2013 brisbane jamboree as well as his ca18det 1200 ute Fonz |
Author: | d [ Thu May 23, 2013 12:42 am ] |
Post subject: | Re: Datsun 1000 Project :) |
There is a nice sedan in the same red in Japan lowered with awesome wheels but cant find the pics atm. ca18det will be a rocket. |
Author: | da fonz [ Thu May 23, 2013 7:36 am ] | ||
Post subject: | Re: Datsun 1000 Project :) | ||
this one d?
|
Author: | d [ Thu May 23, 2013 2:05 pm ] |
Post subject: | Re: Datsun 1000 Project :) |
4 door! http://img110.imageshack.us/img110/8716/r00106347da.jpg |
Author: | da fonz [ Tue Jun 04, 2013 9:36 pm ] | ||
Post subject: | Re: Datsun 1000 Project :) | ||
Ill just leave this here
|
Author: | k-man 79 wagon [ Tue Jun 04, 2013 10:10 pm ] |
Post subject: | Re: Datsun 1000 Project :) |
Mad dude |
Author: | da fonz [ Sun Jul 07, 2013 9:31 am ] | |||
Post subject: | Re: Datsun 1000 Project :) | |||
hey guys, been a while since i posted pics so here are a couple from yesterday. fitted my xr6 intercooler and made sure it clears the grill and beaver panel. also got a new exhaust manifold as the other one sat too high. waiting my my shortened axels to come back from being re splined then diff will be going in. sort out my tailshaft and it will be able to start, run and drive Fonz
|
Page 1 of 1 | All times are UTC+11:00 |
Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |