You need to bridge these two wires [Black with Yellow tracer], that takes the place of the Inhibitor switch contacts: -
Attachment:
510 Inhibitor switch bypass.jpg [ 138.41 KiB | Viewed 2356 times ]
| OZDAT http://ozdat.com.au/forum/ |
|
| 1600 wont crank http://ozdat.com.au/forum/viewtopic.php?t=29923 |
Page 1 of 3 |
| Author: | jono83 [ Sun Oct 21, 2012 8:55 pm ] |
| Post subject: | 1600 wont crank |
Ok this thing is realy starting to anoy me to the point im reasy to burn it lol The original loom was hacked up and bits added on every were So I thought I would get a new loom got one that was standard not cut choped or anything put It in and it wont crank any ideas im stumped Starter is fine Changed both engine and dash loom |
|
| Author: | datdrift [ Mon Oct 22, 2012 3:07 pm ] |
| Post subject: | Re: 1600 wont crank |
does it crank when u put a screw driver across the solinoid? got dash lights ,charge/oil ? |
|
| Author: | Nissanman [ Mon Oct 22, 2012 3:53 pm ] |
| Post subject: | Re: 1600 wont crank |
Assuming you have the wiring correct, you may have an AUTO loom instead of a MANUAL or vice-verse. The AUTO loom has extra wiring for the INHIBITOR switch which needs to be bridged out on a MANUAL trans. car. Time to do some fundamental checks as ^^ said. |
|
| Author: | jono83 [ Mon Oct 22, 2012 7:47 pm ] |
| Post subject: | Re: 1600 wont crank |
Yes its a auto loom I just found out starter is fine what needs to be done to get it to crank |
|
| Author: | Nissanman [ Mon Oct 22, 2012 7:55 pm ] |
| Post subject: | Re: 1600 wont crank |
You need to bridge these two wires [Black with Yellow tracer], that takes the place of the Inhibitor switch contacts: - Attachment: 510 Inhibitor switch bypass.jpg [ 138.41 KiB | Viewed 2356 times ] |
|
| Author: | jono83 [ Mon Oct 22, 2012 8:07 pm ] |
| Post subject: | Re: 1600 wont crank |
I only have a thing with three wires going to it and two are the yellow and black and one with yellow black with red trace and in all the diagrams there are 4wires am I looking at the right bit |
|
| Author: | Nissanman [ Mon Oct 22, 2012 8:12 pm ] |
| Post subject: | Re: 1600 wont crank |
Sounds like you are hot on the trail. Get someone to turn the key to START and you should see 12V on one of the BY wires. The other BY wire should go to the spade terminal at the starter. If so, join the two BY wires together and you should be good to go 
|
|
| Author: | jono83 [ Mon Oct 22, 2012 8:25 pm ] |
| Post subject: | Re: 1600 wont crank |
Ok ill try it |
|
| Author: | jono83 [ Mon Oct 22, 2012 8:42 pm ] |
| Post subject: | Re: 1600 wont crank |
Ok I have just done it nothing so I got a test light went to my ignition barrel and put the tester on the black and yellow wire turn the key and nothing no power does that mean my ignitions stuffed ? |
|
| Author: | Nissanman [ Mon Oct 22, 2012 8:52 pm ] | ||
| Post subject: | Re: 1600 wont crank | ||
Not necessarily. You will need to find the power feed for the START circuit. Have a look at this link and the schematics within. http://www.mediafire.com/?t0932sd6ev7cu You need to look for a schematic for the Auto but apart from the inhibitor switch problem any schematic will suffice.
|
|||
| Author: | jono83 [ Mon Oct 22, 2012 8:55 pm ] |
| Post subject: | Re: 1600 wont crank |
Straight over my head lol |
|
| Author: | jono83 [ Mon Oct 22, 2012 8:59 pm ] |
| Post subject: | Re: 1600 wont crank |
This problem has really pissed me of im ready to burn it now |
|
| Author: | Nissanman [ Mon Oct 22, 2012 9:02 pm ] |
| Post subject: | Re: 1600 wont crank |
I just edited my last post to show a typical START circuit. Are you using a key in the lock or a screwdriver in the switch to crank it? Don't turn the ignition switch too far over to crank the engine if you are just turning the switch, it will go past the correct position and do nothing. You now need to check for some voltages. Have a break and we will try again later
|
|
| Author: | jono83 [ Mon Oct 22, 2012 9:35 pm ] |
| Post subject: | Re: 1600 wont crank |
Using key |
|
| Author: | jono83 [ Mon Oct 22, 2012 10:51 pm ] |
| Post subject: | Re: 1600 wont crank |
Or do I just try find a manual loom |
|
| Page 1 of 3 | All times are UTC+11:00 |
| Powered by phpBB® Forum Software © phpBB Limited https://www.phpbb.com/ |
|